Axis 1 Instrukcje Operacyjne

8Sliding Motor Mount RailHub ScrewController ConnectorGear Hub

9The HPM-1 Motor and ExtrasHub ScrewGear Hub0.8 Mod Gear0.6 Mod Gear0.5 Mod Gear19mm Rod Clamp15mm Rod Clamp

10The Axis1 consists of three main components; The hand unit, the receiver and the motor. Mount the receiver unit on your camera. Using Velcro or Tu

11Getting StartedDO NOT DO THIS IF YOU ARE USING A ENDLESS INFINATE ROTATING DSLR LENS. SEE THE INFINATE ROTATION SECTION OF THIS MANUAL FIRST. The mo

• 12The motor features a sliding rod mount slot so the motor can be height adjusted to achieve convenient mesh with the lens. There are 15 and 19mm ro

13Mounting the HPM-1 Mesh the motor gear to the lens. It is not important where the lens is in its range, there is no need to ensure the lens is in th

14Setting the ChannelThe motor features a sliding rod mount slot so the motor can be height adjusted to achieve convenient mesh with the lens. There a

Mesh the motor gear to the lens. It is not important where the lens is in its range, there is no need to ensure the lens is in the middle or away from

16Lens Calibration To initiate an auto calibrate routine, press and hold either of the two calibrate buttons. There is a calibrate button on both the

Checking the signal strength A signal strength report is automatically displayed on the hand unit LED display after a channel check. To check the sign

Soft Stops The hand unit has two user denable soft stops that are particularly useful with long lens or macro work. You can choose a smaller area of

19Soft StopsRun/StopThe Axis1 has a ve pin 0B Lemo on the receiver unit to interface with various cameras to control camera run. The connector is set

Hand unitThe Axis1 hand unit accepts a Canon LP-E6 style lithium battery. You can use the Canon batteries or any of the third party equivalents. From

21PowerLow receiver battery warningIf the power supply powering the receiver unit runs below 10v, then a warning will show on both the hand unit and t

When using modern DSLR lenses that have no physical stop on the focus ring, auto calibration cannot be used. These lenses must be calibrated manually

23Innate Rotation Mode You can now move the knob around inside the calibrated positions. Please note that innitely rotating DSLR lenses were never b

24ComplianceFCC warning statementThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This dev

25 Connector PinoutsConnector PinoutsRX Power - 0B 2pin Lemo Pin 1 - +12vPin 2 - GNDRun/stop - 0B 5pin Lemo Pin 1 - +3.3v output (for RED Epic/Scarle

L.E.D Display KeyU.C - Uncalibrated U.P - Unplugged motor H.0-9 - Strength of signal being received by the hand unitr.0-9 - Strength of signal being r

L.E.D Display KeyConnector PinoutsRX Power - 0B 2pin Lemo Pin 1 - +12vPin 2 - GNDRun/stop - 0B 5pin Lemo Pin 1 - +3.3v output (for RED Epic/Scarlet on

1ContentsContentsPlease Read FirstStandard Package ContentsThe Hand UnitThe Receiver UnitThe HPM-1 Motor and ExtrasGetting StartedMounting the HPM-1 S

Manual | Simon Langley Designhttp://simolango.wix.com/[email protected]

2- Do not overtighten any rod clamps or tighten with no rods inserted- Do not press on the membrane panel lights (Limits, Run, Inf.rot)- Do not operat

ContentsPlease Read FirstStandard Package ContentsThe Hand UnitThe Receiver UnitThe HPM-1 Motor and ExtrasGetting StartedMounting the HPM-1 Setting th

4Direction ButtonPower ButtonIndicator LightControl WheelRemovable Marking RingLimit Set ButtonsLanyard StudLimit Set IndicatorsAntennaChannel Change

5The Hand UnitLED DisplayLight SocketBUS PortSide PointerARRI Standard Rosette (M6)Lanyard StudBattery CompartmentBattery Release Lever

Camera Run Connector 6Motor Connector12v DC Power Connector BUS Connector Antenna Connector

7The Receiver UnitAutocalibrate Button Innate Rotation Button And Indicator Channel Button LED Display Mounting Rails