Axis OfficeBasic Parallel Instrukcja Użytkownika Pobierz pdf (Strona 1)

Using Network Printers

This help document describes how to discover, configure, and use TCP/IP network printers with CUPS.

Getting the IP Address

Every network printer or print server has a unique Internet Protocol (IP) address associated with it. This

address is either configured manually or set using an automatic network protocol such as the Boot Protocol

(BOOTP), Dynamic Host Control Protocol (DHCP), Reverse Address Resolution Protocol (RARP), or

ZeroConf.

You can normally find the IP address of a printer on the printer's control panel or by printing the configuration

or status page. The Simple Network Management Protocol (SNMP) can also be used to get the IP address

remotely, which happens automatically when you visit the CUPS administration web page or choose an

available CUPS device when adding a printer.

Configuring the IP Address

When you first install a network printer or print server on your LAN, you need to set the Internet Protocol

("IP") address. Most higher-end "workgroup" printers allow you to set the address through the printer control

panel. However, if you have many printers you will want to assign the addresses remotely - this makes

administration a bit easier and avoids assigning duplicate addresses accidentally.

To setup your printer or print server for remote address assignment, you'll need the Ethernet Media Access

Control ("MAC") address, also sometimes called a node address, and the IP address you want to use for the

device. The Ethernet MAC address can often be found on the printer test page or bottom of the print server.

Configuring the IP Address Using DHCP

The DHCP protocol is the usual way of setting the IP address of a printer on a managed network. Using the

standard dhcpd(8) program supplied with UNIX you simply need to add a line to the /etc/dhcpd.conf file:

host hostname {

hardware ethernet mac-address;

fixed-address ip-address;

}

Make sure that the hostname you use is also listed in the /etc/hosts file or is registered with your DNS server.

Configuring the IP Address Using BOOTP

The BOOTP protocol is used when you need to provide additional information such as the location of a

configuration file to the network interface. Using the standard bootpd(8) program supplied with UNIX you

simply need to add a line to the /etc/bootptab file; for IRIX:

myprinter 08:00:69:00:12:34 192.0.2.2 myprinter.boot

Newer versions of bootpd use a different format:

myprinter:ha=080069001234:ip=192.0.2.2:t144=myprinter.boot

The myprinter.boot file resides in the /usr/local/boot directory by default. If you do not need to provide a

boot file you may leave the last part of the line blank.

1 2 3 4 5 6 7 8 9

Podsumowanie treści

Strona 1 - Using Network Printers

Using Network PrintersThis help document describes how to discover, configure, and use TCP/IP network printers with CUPS.Getting the IP AddressEvery n

Strona 2 - AppSocket Protocol

Note: Some versions of UNIX do not enable the BOOTP service by default. The/etc/inetd.conf or /etc/xinetd.d/bootp file usually contains a line for the

Strona 3

ipp://ip-address-or-hostname/resource?option=valueipp://ip-address-or-hostname/resource?option=value&option=valueipp://ip-address-or-hostname:port

Strona 4 - Common Network Printer URIs

format=r Specifies that the print data is a FORTRAN carriage control file.format=t Specifies that the print data is a troff Graphic Systems C/A/T phot

Strona 5 - Basic Debugging

Kodak® lpd://address/psQMS® CrownNetTMlpd://address/psTektronix® PhaserShareTMsocket://address:9100XEROX® 4512 NIC lpd://address/PORT1XEROX® XNIC lpd:

Strona 6

2 INFO: Using default SNMP Community public 3 DEBUG: Scanning for devices in "public" via "@LOCAL"... 4 DEBUG: 0.000 Sending 4

Strona 7 - Configuring Print Servers

Dissecting the OutputThe first two lines are just informational and let you know that the default community name and address arebeing used. Lines 3-15

Strona 8

ftp> user root331 User name ok, need passwordPassword: pass (this is not echoed)230 User logged inftp> get configlocal: config remote: config200

Strona 9

221 Goodbye.Your Axis print server is now ready for use!Configuring Linksys Print ServersThe Linksys print servers can be configured using BOOTP or DH